Search results

  1. badboyrcg70

    badboys 70 project

    time to start posting up some pictures again here and show more updates
  2. badboyrcg70

    badboys 70 project

    Below are the instructions right off TRZ site. Mine were set at ride height before adding installing the motor. 11. When adjusting for ‘bump steer’, you want to adjust the rod-end height to be as parallel as possible with the working angle of the control arms at race-weight and at ride height...
  3. badboyrcg70

    badboys 70 project

    Sorry for the delay in responding. Rack is set up to slope downward toward tie rod. 3/4-1" if I remember.
  4. badboyrcg70

    badboys 70 project

    Ill try them as well.
  5. badboyrcg70

    badboys 70 project

    Ugggg makes me sick to come here and not see a pictures!
  6. badboyrcg70

    badboys 70 project

    Motor finally made its way in and actually had no issues with interference of the rack and pinion or the mid plate. Something finally went easy.
  7. badboyrcg70

    Like New Manual Steering box and arm for 2nd gens.

    My stock power steering box arm didn't work so I had to order the correct one from jegs. This will bolt right up complete with new rag joint as well.
  8. badboyrcg70

    Like New Manual Steering box and arm for 2nd gens.

    Need this gone. Price drop 225.00 shipped
  9. badboyrcg70

    Hi/Low beam switch wiring

    The plug that connects to the hi/low beam switch has 3 wires. green goes to high beams tan goes to low beams where does the blue wire connect to?
  10. badboyrcg70

    Like New Manual Steering box and arm for 2nd gens.

    Like the title says its a Borgeson 357 box that was bought and used for mock up then decided to go with a rack and pinion. I also have a brand new steering arm that is the correct length for second gens. The box was 350.00 new and the arm was 75.00 new so 425.00 total. I am asking 275.00 shipped...
  11. badboyrcg70

    badboys 70 project

    Motor back from machine shop. Got some minor things to do to it then get it in there.
  12. badboyrcg70

    badboys 70 project

    Final assembly of motor almost complete.
  13. badboyrcg70

    Advice

    OK got it figured out I think. outside lenses are: black(ground)/Brown(park)/yellow(L) or green(R) are turns inside lenses from what I see are: black(ground)/green(backup) my only question then is that all? So the outer red portion doesn't light up at anytime?
  14. badboyrcg70

    Advice

    I have 2 white sockets(1 has 3 wires and 1 only has 2 wires) I also have 2 black sockets which have 3 wires each in them. My thoughts would be that the outer lights would be Taillights/brake and would need 3 wires(Gr/Park/Brake) while the inner would only need 2 or 3? 1 wire is for the back up...
  15. badboyrcg70

    Advice

    First question is its been forever since lights were installed so which ones are for taillights and which is for brake lights/reverse? Next question is what does this go to? Last question is there supposed to be a second wire in the black plug in this picture and what would it go to? Reason...
  16. badboyrcg70

    badboys 70 project

    Got the wood burning stove all hooked up and fired and almost ready for winter. I still want to install a heat reclaimer, but at least I wont need to run my torpedo heater all the time.
  17. badboyrcg70

    badboys 70 project

  18. badboyrcg70

    badboys 70 project

    Progress on the motor has been a struggle waiting on parts and finding issues with parts I already have. Both heads needed to have o-rings welded and needed to be welded beneath seats after pressure test did not have good outcome. Hopefully once they are finished things will wrap up quickly.
  19. badboyrcg70

    badboys 70 project

    Drop off They are spot welded to the quarter and trunk pan. Since your just installing a new one grind/cut it out.
  20. badboyrcg70

    Need some racer help with Cal trac setup issues

    Advice Try following these steps. You didn't mention rear gear and trans ratio. With these tires you need to kill off torque and they seem to like pressures 15-19 range. Most likely you will need better shocks!




Top