454

hi I am planning on building a gen vi 454 with AFR 265cc aluminum heads and a crane cams .632 lift hydraulic roller cam but the application still for it doesn’t have the gen vi 454 listed for it and I’m wondering why I couldn’t use the gen v Hydraulic roller cam on my gen vi 454?

hi I recently built a 454 Camaro and Drove the car around the block a couple times and I took the distributor out to change my intake and noticed an excessive amount of wear on the cam to distributor gear, and I’m wondering if I have the right material distributor gear for it (like steel or...

hey I’m wondering how much hp a 454 with AFR 265cc aluminum heads with a .547 lift hydraulic roller cam and a single S480 turbo with a 80mm compressor wheel and 96mm exhaust side with 1.32A/R and a t6 flange would produce and how fast it would spool on the drag strip, also I have heard people...

Hi I have a 454 bored .60 over with port and polished cast heads with a .547 Hydraulic roller cam with a 750 carb and will occasionally be using nitrous, this will be a drag strip engine and I’m wondering if a single or dual plane intake would be best for this build?

Hi I got a 454 4 bolt main that is bored .60 over with a stock bottom end other than Hypereutectic flat top pistons, with stock heads with some port and polishing and a .547 hydraulic roller cam, and titanium rocker arms. This engine will be for drag racing, and I’m wondering what is the maximum...

hi I’m wonder what are the best aluminum heads for a 454 that I can get for under $3,000 for the pair? I’m going to be using these on the drag strip in a 3,400lb Camaro, and I’m looking to get the most power out of this 454 naturally aspirated. Also which would be better for drag racing a 454...

Located in 32221, pickup or buyer pays shipping. Upload pics when I get a chance, until then here's the fb market listing https://www.facebook.com/marketplace/item/165567578120997/ 454 parts will sell separate or all for $800 obo. Was going to build a 496, but decided to go with a Dart block so...

This just came out of a late eighties mark iv 454. First lobe has a chip. Judging purely by how it feels running my finger over the damaged lobe, that is the only lobe that kinda feels like it has a flat spot at the top. Almost like a very small ridge on either side of the chip, whereas any...

Any AZ local have a spare 454 crank (going in 78 block) for cheap? Local shops are crazy expensive.

Hey guys! So this summer I blew up the 350 that was in my 79 Z. I'm trying to figure out how to go about getting her back on the road by spring. Was thinking I would have the 350 rebuilt, but the engine shop offered to sell me a 454 that they have for the same as they would charge to do a...

1970 Camaro Rally Sport Split Bumper $44,500 • 454 engine professionally rebuilt by Angelluci Performance • 700R4 automatic transmission with Posi-Traction • 1st place at 2013 Camaro Superfest modified 1970-73 • Less than 3000 miles since total rebuild • Black interior with 2012 Camaro...

Up for sale. Vintage set of bbc Appliance headers in great shape. Catalog picture I have only goes to 1971, but I would guess these headers would fit at least to up to 76? If you like the impressive look of big tube “spaghetti” headers? Then you need to check these out. Buyer to determine their...

Hi. I'm looking for all brackets for alternator, A/C compressor and power steering for a 454. Also need pulleys, flywheel, water pump and starter. Just bought a used long block and need all these components in order to install in my 74 Type LT. Would need shipped to Miami, FL. Feel free to...

Take a look at this Craigslist ad and tell me what you think this 454 car is worth in today's old car market. The trunk has a spot about the size of a quarter that is rusted through and the car was factory equipped with a vinyl top. https://shoals.craigslist.org/cto/6024640322.html

I currently have a 79 z28 Camaro that I have been drag racing a few years, now. It currently has a decent 355 in it right now. I am wanting to slowly build my dream blower motor and drop it in the Z when it is finished. My dream motor since I was young was to have a blower sticking out of the...

After by YOUNGIN71Z28 posted Dec 11, 2016 at 2:13 AMBefore by YOUNGIN71Z28 posted Dec 11, 2016 at 2:13 AMBig Block Chevy by YOUNGIN71Z28 posted Dec 11, 2016 at 2:13 AMHello all those of Nasty-Z28 my name is Anthony and I'm an owner of a 1971 Camaro that I restored throughout high school and will...

I have a 454 I got for a trade recently and am going to drop this into my 77 camaro, but I'm still trying to figure out what it is.? -Block number is 3963512 -Vin number is T1008CGU -Partial Vin is 10R1153 Here is where I'm very confused, drive head is a 336781 head dated "D 7 76" but the...

Looking for which sparkplugs I can use with a gen v 454 stock 10114156 open chamber head now using domed pistons 9.7:1 compression Stock pistons were flat tops would the stock sparkplug be too long?

Looking for which sparkplugs I can use with a gen v 454 stock 10114156 open chamber head now using domed pistons 9.7:1 compression Stock pistons were flat tops would the stock sparkplug be too long?

1971 Camaro Hugger Orange w/ pearl and silver rally stripes Done by Surfside Collision Brick NJ 454 Bored .30 over Built by Tims Machine Shop In Toms River NJ Crane Roller Cam, Crane Gold Roller Rockers, Pro Comp aluminum heads 700 R4 Transmission rated at 600hp w/Bow Tie Overdrive TV...