/ Register

C6 ZO6 wheel fitment

Discussion in 'Suspension, Steering, Brake & Wheel Topics' started by Olympia77camaro, May 31, 2014.

Page 1 of 2
  1. May 31, 2014 #1
    Olympia77camaro

    Olympia77camaro New Member

    Messages:
    19
    Likes Received:
    0
    Joined:
    May 31, 2014
    Location:
    Murfreesboro, Tennessee
    I am brand new to this forum but I must say it is the best, I am getting new rims for my 1977 camaro and I am not very knowledgeable of the fitment. They are C6 ZO6 rims that are 17×8.5 fronts and 18×9.5 rears. Both are +56 offset. The bolt pattern is 5×4.75. Will I need adapters? If so what size up front and what size rear? Thank you so much for all the help and feedback!!
     
  2. May 31, 2014 #2
    dcozzi

    dcozzi Veteran Member

    Messages:
    3,894
    Likes Received:
    954
    Joined:
    May 1, 2002
    Location:
    Phoenix, AZ
    Try using the search feature on here for Z06 wheels.
     
  3. May 31, 2014 #3
    Curves

    Curves Member

    Messages:
    32
    Likes Received:
    0
    Joined:
    Aug 19, 2013
    Location:
    Olympia WA
    You're definitely going to need adapter/ spacer, +56 is 7.45" backspace for the rear and 6.95" for the front.

    On the back you could probably do a 1.5" adapter depending on the look you want.

    On the front you can use a spacer, I would put the wheel and tire on and use washers to move it out in increments until the tire stops hitting the sway bar at full turn. Then just measure your stack of washers to determine the spacer you need, probably 1/4" to 1/2".
     
    Last edited: Jun 1, 2014
  4. May 31, 2014 #4
    Olympia77camaro

    Olympia77camaro New Member

    Messages:
    19
    Likes Received:
    0
    Joined:
    May 31, 2014
    Location:
    Murfreesboro, Tennessee
    Thank you Curves! Why do I need the adapter if the bolt pattern is the same as my hub? Do I just get a 5×4.75 1 inch adapter or a 1 inch spacer for rear? Im sorry I am not very knowledge with wheel sizes and fitments
     
  5. May 31, 2014 #5
    Curves

    Curves Member

    Messages:
    32
    Likes Received:
    0
    Joined:
    Aug 19, 2013
    Location:
    Olympia WA
    The adapter is needed because a spacer that big will swallow up all your stud and you won't have any meat left to get a nut on.

    It keeps the same bolt pattern
     
    Last edited: Jun 1, 2014
  6. May 31, 2014 #6
    Olympia77camaro

    Olympia77camaro New Member

    Messages:
    19
    Likes Received:
    0
    Joined:
    May 31, 2014
    Location:
    Murfreesboro, Tennessee
    So just get an adapter that is same bolt pattern?
     
  7. May 31, 2014 #7
    Curves

    Curves Member

    Messages:
    32
    Likes Received:
    0
    Joined:
    Aug 19, 2013
    Location:
    Olympia WA
    Yep
     
  8. Jun 1, 2014 #8
    Olympia77camaro

    Olympia77camaro New Member

    Messages:
    19
    Likes Received:
    0
    Joined:
    May 31, 2014
    Location:
    Murfreesboro, Tennessee
    Thank you for your information!! If you don't mind, what tires should I run with these specs?
     
  9. Jun 1, 2014 #9
    Curves

    Curves Member

    Messages:
    32
    Likes Received:
    0
    Joined:
    Aug 19, 2013
    Location:
    Olympia WA
    Again, depending on the look you want.....

    I would go with a 275 on the rear and a 245 on the front.
     
  10. Jun 1, 2014 #10
    Olympia77camaro

    Olympia77camaro New Member

    Messages:
    19
    Likes Received:
    0
    Joined:
    May 31, 2014
    Location:
    Murfreesboro, Tennessee
    Ok thank you so much for all your help!!
     
Page 1 of 2

Share This Page