WTB Two 1970 Rear Bumper Guard (Fangs) 1/4-20 Bolts

Discussion in 'Swap Meet Section' started by bkmont, Nov 24, 2017.

  1. bkmont

    bkmont Veteran Member

    Messages:
    1,181
    Likes Received:
    102
    Joined:
    Nov 14, 2010
    Location:
    Pensacola, Florida
    Hello,
    Looking for two 1/4-20 OEM bolts that attach the rear bumper guards (fangs) to the rear lower tail panel on a 1970 Z28.
    Thanks,
    Bryan
     
  2. Double J

    Double J Veteran Member

    Messages:
    411
    Likes Received:
    15
    Joined:
    Jan 23, 2008
    Location:
    Michigan
  3. badazz81z28

    badazz81z28 Veteran Member

    Messages:
    19,196
    Likes Received:
    1,083
    Joined:
    May 4, 2001
    Location:
    Alabama
    They have a minimum, I know I got them, let me dig them out
     
  4. bkmont

    bkmont Veteran Member

    Messages:
    1,181
    Likes Received:
    102
    Joined:
    Nov 14, 2010
    Location:
    Pensacola, Florida
    Thank you! If you find them, let me know what I owe you.
    Bryan
     
  5. badazz81z28

    badazz81z28 Veteran Member

    Messages:
    19,196
    Likes Received:
    1,083
    Joined:
    May 4, 2001
    Location:
    Alabama
    This is what I got
     

    Attached Files:

  6. roeville

    roeville Veteran Member

    Messages:
    1,276
    Likes Received:
    116
    Joined:
    Oct 9, 2000
    Location:
    SF East Bay CA
    Bryan,
    Here’s a picture of the screws from my 71. I’m not 100% sure they’re original but these are obviously not 1/4”-20.
    Mike
    068F5633-F193-4B39-802D-B07C6BD3D249.jpeg
     
    Last edited: Nov 26, 2017
  7. bkmont

    bkmont Veteran Member

    Messages:
    1,181
    Likes Received:
    102
    Joined:
    Nov 14, 2010
    Location:
    Pensacola, Florida
    Hey guys appreciate the responses. I'm just going by what I remember the hardware looked like on my Citrus Z. Here's some pics of a NOS hardware kit. I'm not sure if it differed from the assembly line hardware. It looks like the AMK B-10384 bolt (see pic) will be close. My car has the fangs hanging from the bumper with the 1/2" holes in what appears to be the original tail pan. I guess the rubber grommets were removed during paint and were not reinstalled. If I can't find any from a forum member, I'll just have to come up with a $30 minimum order which probably won't be too hard to do.
    Bryan
     

    Attached Files:

    Last edited: Nov 26, 2017
  8. CamarosRus

    CamarosRus Veteran Member

    Messages:
    8,527
    Likes Received:
    145
    Joined:
    Feb 16, 2000
    Location:
    Auburn,WA (between Sea & Tac)
    This same subject was discussed YEARS ago at NastyZ28......I was hoping I had pics
    from Jack Seymour's 22K survivor but dont...What about the 1100 mile Z that Charley
    L had ????......
     
  9. 70lt1z28

    70lt1z28 Veteran Member Gold Member

    Messages:
    3,952
    Likes Received:
    871
    Joined:
    Oct 3, 1999
    Location:
    Beavercreek, Ohio, USA
    Here is the AIM page:
    upload_2017-11-26_11-7-10.png

    AMK does not list the #6 180022 bolt, but does list the 3903539 well nut:
    upload_2017-11-26_11-14-14.png
    It's 1/4-20, so what bkmont lists in post 7 appears to be correct. The finish on the bolts is what is in question now.
     
  10. bkmont

    bkmont Veteran Member

    Messages:
    1,181
    Likes Received:
    102
    Joined:
    Nov 14, 2010
    Location:
    Pensacola, Florida
    According to the AMK catalog, the bolt they are selling is S8 = Zinc (Dark Silver - Blue). 1,100 mile Z28 shows a silver finish with a M head mark.
    IMG_3256.JPG
     

Share This Page