Official Pay it Forward thread :)

[chambr]

I'm in for the HEI parts (if they are still available).. how do you want to be paid.. shipping to Orlando Florida...

Let me know ..

Thanks - Mike-

 

[Chuck 706]

I have a partial Pypes crossflow system

It's the intermediate, tail and muffler. Less than 200 miles on them. I just have no room to store them and have no need.

Pay shipping, around $60.00 or pick them up in south central Nebraska.

 

[ATM]

It's the intermediate, tail and muffler. Less than 200 miles on them. I just have no room to store them and have no need.

Pay shipping, around $60.00 or pick them up in south central Nebraska.

2.5"? Very interested. Does it fit on a second gen?

 

[Chuck 706]

More items need a home.

I also have the original a/c condenser and evaporator, the complete rear brakes and a rusty old set of small block headers.
The drums, shoes and cyls are new on the brakes.

Again just pay shipping or pick them up here. I'll have more later.

Photos are in the "Stuff" album of my PhotoBucket site.

 

[Chuck 706]

2.5"? Very interested. Does it fit on a second gen?

That's what it's for. I just took it off of my 76.

 

[camaro73lt]

Need A Trunk Lid w/Spoiler?

Original trunk lid from a 73 w/factory drilled holes for tall spoiler. No rust of any significance. Straight and factory correct. maybe a surface spot here or there. Been stored for years. Also has center section Tall Spoiler (OEM piece). Missing a few studs but no cracks or chips.

Must pick up in Germantown, Maryland. Will not ship. - Free to good home.

 

[Printstron]

Intake and Exhaust Manifolds, Rear seat bases.

I have an intake manifold and exhaust manifolds and rear seat bottoms (no top section). From a 73 LT. Free with paid shipping.

I had two sets of seat bottoms, and doing a stroked motor so I don't need. I feel bad trashing these especially if one of you out there is doing a restoration and not a mod.

I also have the A/C box.

[/url]
IMG_1539 by printstron, on Flickr[/IMG]

[/url]
IMG_1538 by printstron, on Flickr[/IMG]

[/url]
IMG_1537 by printstron, on Flickr[/IMG]

[/url]
IMG_1540 by printstron, on Flickr[/IMG]

[/url]
IMG_1536 by printstron, on Flickr[/IMG]

[/url]
IMG_1534 by printstron, on Flickr[/IMG]


Just let me know.

Vic

 

[speed_m5]

hey guys I have a passenger side T-top from a 81 Z28 FREE if local come get it or pay for shipping it is in Baytown Texas 77520

 

[krausery]

I have a few left over pieces of sheet metal from when I was doing my floors.

Local pickup is preferred, shipping this stuff would be difficult as I in my infinite wisdom threw out all the boxes...

I'm located in Daytona Florida so send me a PM if interested!

I was going to sell this stuff (I had a thread made, but I deleted it) but decided to give it all away instead!

Floor Parts:

Forward Floor Brace (Should fit early second gen I believe):

Closeup of 78-81 driver's side pan: GONE-Thanks!!

Closeup of early 2nd gen driver's side pan:

Closeup of various other pieces:

Hey man! I wish I had these about a year ago!! had to buy some of those exact patch panels. Although I had to replace the passenger back seat pan and need to find that bracket that the back seat goes into. Any of those lying around??

 

[mgoad1971]

Free plus shipping. Complete set of fender flares including the front air dam piece that goes under the nose, for late 2nd gen trans am (79-81 I think?). Scruffy but intact and not busted up. I will provide pics if you are interested.

pm sent